<VV> Power glide

[Joel McGregor]

I haven't built one yet but I have a couple torn down and am doing some research between other projects.  Thinner plates and cutting the piston should allow for more plates hopefully.

From: James Davis <hurricanehazel16 at gmail.com>
Sent: Monday, December 03, 2018 6:18 PM
To: Joel McGregor <joel at joelsplace.com>
Cc: James Koenig <mrkoenig3 at gmail.com>; VV List <virtualvairs at corvair.org>
Subject: Re: <VV> Power glide

TCI <http://www.tciauto.com/tc/transmissionshtml/> has several types and thicknesses of clutch disk for Corvair PowerGlides (same as cast iron case PG).  Note than the steels are different between car and Corvair PowerGlides and the Corvair uses smaller number of disk in the clutch packs than car PowerGlide.. Yes all Corvair powered and all 500 series V-8 UltraVans came with PowerGlide transmissions.  That said, 3.0 and 3.1 liter Corvair engine can develop sufficient torque to overcome the 1964-1969 Corvair PowerGlide.  Fortunately Ken Arnold developed internal parts to overcome the stock limitations and hold the toque of his 215 cuin V-8 Corvair and Billy Bruce's 1963 Corvair Turbo drag car.
Jim Davis

On Mon, Dec 3, 2018 at 3:25 PM Joel McGregor via VirtualVairs <virtualvairs at corvair.org<mailto:virtualvairs at corvair.org>> wrote:
We are lucky that we can get any parts for the Corvair Powerglide.  Very few are in common with the big car PG so I doubt you can get any Kevlar parts.  Clark's has them ready to go.
I just compared parts recently but can't remember.  I think the low/reverse 350 plates are the same as one set in the Corvair.
The good news is I don't think the stock Corvair PG in good condition has any issues handling any amount of power a Corvair engine is capable of.  They used them in Ultravans.

-----Original Message-----
From: VirtualVairs <virtualvairs-bounces at corvair.org<mailto:virtualvairs-bounces at corvair.org>> On Behalf Of Old men rule racing via VirtualVairs
Sent: Saturday, December 01, 2018 7:36 AM
To: virtualvairs at corvair.org<mailto:virtualvairs at corvair.org>
Subject: <VV> Power glide

Hi all... After putting the car on the lift, we have determined that we need a new power glide. Who has one with Kevlar clutches and is ready to install?
Jim
 _______________________________________________
This message was sent by the VirtualVairs mailing list, all copyrights are the property of the writer, please attribute properly. For help, mailto:vv-help at corvair.org<mailto:vv-help at corvair.org> This list sponsored by the Corvair Society of America, http://www.corvair.org/ Post messages to: VirtualVairs at corvair.org<mailto:VirtualVairs at corvair.org> Change your options: http://www.vv.corvair.org/mailman/options/virtualvairs
Archives: http://www.vv.corvair.org/archive.htm
 _______________________________________________
 _______________________________________________
This message was sent by the VirtualVairs mailing list, all copyrights are the property
of the writer, please attribute properly. For help, mailto:vv-help at corvair.org<mailto:vv-help at corvair.org>
This list sponsored by the Corvair Society of America, http://www.corvair.org/
Post messages to: VirtualVairs at corvair.org<mailto:VirtualVairs at corvair.org>
Change your options: http://www.vv.corvair.org/mailman/options/virtualvairs
Archives: http://www.vv.corvair.org/archive.htm
 _______________________________________________