<VV> Plug wire lengths ?

[Charles Lee]

You're right about that !  I noticed that the skimpy little boots that
they do have are loose and would likely be blown up the wire !

So, I brought them back for a refund that I applied to a set of Seth's
silicon wires ...

Thanks for the input !

Charlie

-----Original Message-----
From: Harry Yarnell [mailto:hyarnell1 at earthlink.net] 
Sent: Saturday, September 13, 2008 4:19 PM
To: Charles Lee; 'J R Read_HML'; virtualvairs at corvair.org
Subject: Re: <VV> Plug wire lengths ?


Uh, do these 'generic' wires have the correct boot seal at the plug end?
If 
not, you're losing cooling air out the plug hole.

Harry Yarnell
Perryman garage and orphanage
Perryman, MD
hyarnell1 at earthlink.net
----- Original Message ----- 
From: "Charles Lee" <chaz at ProperProPer.com>
To: "'J R Read_HML'" <hmlinc at sbcglobal.net>; <virtualvairs at corvair.org>
Sent: Saturday, September 13, 2008 5:47 PM
Subject: Re: <VV> Plug wire lengths ?


> Right !  These are generic, and will probably go back to NAPA, but I 
> figured I'd get the car running while I order some from a l'Vair club 
> member.
>
> No 90 degree bend, but that would make not up the length I need - #2 
> is tight too, so back they go.
>
>
>
> -----Original Message-----
> From: virtualvairs-bounces at corvair.org 
> [mailto:virtualvairs-bounces at corvair.org] On Behalf Of J R Read_HML
> Sent: Saturday, September 13, 2008 2:01 PM
> To: Charles Lee; virtualvairs at corvair.org
> Subject: Re: <VV> Plug wire lengths ?
>
>
> I think the factory ones had a 90 degree bend just before the boot. 
> I've not seen that style in a while.  Maybe that is the problem?  I've

> never actually measured any of them.
> Later, JR
>
> ----- Original Message -----
> From: "Charles Lee" <chaz at ProperProPer.com>
> To: <virtualvairs at corvair.org>
> Sent: Saturday, September 13, 2008 3:58 PM
> Subject: <VV> Plug wire lengths ?
>
>
>> Hi again,
>>
>> What are the factory spark plug wire lengths ?
>>
>> I bought a set (in a pinch) from NAPA, and in order of length, I 
>> installed them 6-4-2-5-3-1.
>>
>> It seems that #3 is too short : 13" end-to-end and won't reach the 
>> plug.
>>
>> #1 is even shorter.
>>
>> Is the set wrong, or is it something else ?
>>
>> Thanks
>> Charlie
>> Orphaned 1967 Monza 110 PG Coupe
>>
>> _______________________________________________
>> This message was sent by the VirtualVairs mailing list, all 
>> copyrights
>
>> are
>> the property
>> of the writer, please attribute properly. For help, 
>> mailto:vv-help at corvair.org This list sponsored by the Corvair Society

>> of America, http://www.corvair.org/
>> Post messages to: VirtualVairs at corvair.org
>> Change your options:
>> http://www.vv.corvair.org/mailman/options/virtualvairs
>> _______________________________________________
>
> _______________________________________________
> This message was sent by the VirtualVairs mailing list, all copyrights

> are the property of the writer, please attribute properly. For help, 
> mailto:vv-help at corvair.org This list sponsored by the Corvair Society 
> of America, http://www.corvair.org/ Post messages to: 
> VirtualVairs at corvair.org Change your options: 
> http://www.vv.corvair.org/mailman/options/virtualvairs
> _______________________________________________
>
> _______________________________________________
> This message was sent by the VirtualVairs mailing list, all copyrights

> are
> the property
> of the writer, please attribute properly. For help, 
> mailto:vv-help at corvair.org
> This list sponsored by the Corvair Society of America, 
> http://www.corvair.org/
> Post messages to: VirtualVairs at corvair.org
> Change your options: 
> http://www.vv.corvair.org/mailman/options/virtualvairs
> _______________________________________________
>